300zx Keyless Entry Remote Control Computer Module Location
this is an article about the nissan 300zx keyless entry remove control you buy to program [2227], Last Updated: Sat May 18, 2024
zcar
Mon Jul 14, 2008
2 Comments
1629 Visits
i have a 1996 nissan 300zx and i bought a keyless entry remove but it doesnt work. the ad said it would work on 94 95 96 but it doenst work on mine,
so i looked at the keyless entry relay and it has a different number, i has a269zua072 and on the remove it says a269zua073
94 95 96 NISSAN 300ZX KEYLESS REMOTE A269ZUA073 w/PROG
A269ZUA073
the box says:
Cont assy-keyless
part no: 29594 48PON
FCCID: A269ZUA072
DOC CERT: No DOC/MDC 7005972
this device complies with FCC rule part 15 Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. this device must accept any interference that may be received including interference that may cause undesired operation
Made in Japan 12v dc Negative GND
Serial H50920979
i bought a FOB on ebay which the seller put for 96 (A269ZUA073), but it didnt work what i need is a A269ZUA072
so i looked at the keyless entry relay and it has a different number, i has a269zua072 and on the remove it says a269zua073
94 95 96 NISSAN 300ZX KEYLESS REMOTE A269ZUA073 w/PROG
A269ZUA073
the box says:
Cont assy-keyless
part no: 29594 48PON
FCCID: A269ZUA072
DOC CERT: No DOC/MDC 7005972
this device complies with FCC rule part 15 Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. this device must accept any interference that may be received including interference that may cause undesired operation
Made in Japan 12v dc Negative GND
Serial H50920979
i bought a FOB on ebay which the seller put for 96 (A269ZUA073), but it didnt work what i need is a A269ZUA072
Vman
Thu Sep 29, 2011
zcar
Wed Sep 08, 2010
if you want to program the keyfob just follow these step by step and it should work, if it doesnt work, try replacing the battery. usually if you buy those things on ebay, they suck..
1. Get inside your Z and close all doors.
2. Release the rear hatch with the lever by the driver's seat.
3. Lock the driver's door.
4. Insert the key in the ignition and then quickly remove it - six times in succession within 10 seconds. (6 in-and-outs within 10 seconds.)
5. Unlock and then re-lock the driver's door. (Don't open the door!)
6. Press a button (once!!) on your remote. (I used the big, "lock doors" button.)
7. Repeat steps 5 and 6 quickly if you have other remotes that you want to program.
8. Step out of your car and test the keyless remotes.
1. Get inside your Z and close all doors.
2. Release the rear hatch with the lever by the driver's seat.
3. Lock the driver's door.
4. Insert the key in the ignition and then quickly remove it - six times in succession within 10 seconds. (6 in-and-outs within 10 seconds.)
5. Unlock and then re-lock the driver's door. (Don't open the door!)
6. Press a button (once!!) on your remote. (I used the big, "lock doors" button.)
7. Repeat steps 5 and 6 quickly if you have other remotes that you want to program.
8. Step out of your car and test the keyless remotes.
Related Content
- For Sale Really Nice Nissan 300zx Twin Turbo Z32 1996 Nice Car
- 1996 Nissan 300zx Bose Radio Cd Stereo Used For Sale Cheap
- Sporty And Stylish New 300zx Front Bumper For Sale Rare Bumper
- How To Set Or Chage Timing Nissan 300zx With A Timing Gun
- 300zx Problem Engine Shuts Down When In Neutral
- How To Pass Smog Check Nissan 300zx Z32 - Car Preparation
- Process On How To Replace Timing Belt On Nissan Car 300zx
- How To Remove A Motor Engine From A Nissan 300zx Car
- How To Install A Cat Back System Exhaust On 300zx Z32 Car
- Failed Smog Check Emissions Test California Nissan 300zx Co(ppm) Vir
Vman
https://www.wallpaperama.com/forums/300zx-keyless-entry-remote-control-t6215.html